!
!
!

Austro - Daimler

Not sure if this actually belongs in Austria or the USA, so I've put it in both countries. Set includes 2 x down tube (221 mm x 27 mm), 2 x head/seat tube (40 mm x 51 mm), 1 x tubing decal

Cannondale

Set includes 2 x down tube (280 mm x 27 mm), 2 x handmade (200 mm x 8 mm), 1 x headbadge (41 mm x 37 mm), 2 x caad (please specify what caad number required)

Centurion V1

Set includes 2 x down tube (200 mm x 23 mm), 2 x Seat Tube (200 mm x 23 mm), 2 x professional (77 x 15 mm)

This is version 1. There are other ones out there, but at this moment this is the only one I have in my library.

Coyote

Set includes 2 x down tube (233 mm x 28 mm), 2 x easton (103 mm x 10 mm), 1 x headbadges (61 mm x 57 mm).

Greg Lemond

Suitable for all frames including steel frames.
Set includes 2 x down tube (175 mm x 24 mm), 1 x seat tube - small GL (26 mm x 22 mm), 1 x head - GL (48 x 41 mm), 2 x seat stays (10 x 72 mm), 2 x maillot jaune (92 x 15 m)

GT Karakoram K2

Set includes 2 x Karakoram (300 x 28 mm), 2 x GT All Terra (111 x 28 mm), 1 x head/seat (70 x 79 mm)

GT Palomar

Set includes 2 x Palomar (200 x 22 mm), 2 x GT (120 x 20 mm), 2 x head/seat (43 x 40 mm)

GT Tempest

Set includes 2 x Tempest (179 x 25 mm), 2 x GT (240 x 40 mm), 1 x head (43 x 40 mm)

HUFFY

Set includes 2 x down tube (131 x 30 mm), 2 x seat tube (131 x 30 mm), 2 x top tube True Temper (128 x 17 mm) 2 x Huffy made in USA printed decals. Various colours available, USA logos willaways be as pictured

Jamis quest

Circa 2003 Jamis quest, not sure if this should be in classic or modern, so I've shown it in both! Digitally re-created and printed onto top quality vinyl. Set includes 2 x down tube (245 x 20 mm), 2 x top tube (147 x 16 mm), 1 x tubing decal (853). Seen here on a silver background (not included) Other colours may be available. info@wanit.co.uk

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Klein V1

Set includes 2 x down tube (220 mm x 35 mm), 2 x seat tube (176 mm x 28 mm), 1 x headbadge (50 mm x 50 mm).

Klein V1 (Pulse)

Set includes 2 x down tube (142 mm x 32 mm), 2 x Pulse (128 mm x 28 mm), 1 x headbadge (50 mm x 50 mm), 1 x seat tube (as head 50 mm x 50 mm) 

Klein V3 (Pulse Comp)

Set includes 2 x down tube (142 mm x 32 mm), 2 x Pulse Comp (132 mm x 20 mm), 1 x headbadge (50 mm x 50 mm), 1 x seat tube (as head 50 x 50 mm)

Kona

Set includes 2 x down tube (190 mm x 30 mm), 2 x seat tube (159 mm x 25 mm), 2 x small (95 x 15 mm)

Land Shark

Not sure if this should be in modern or classic,so I have listed in both! Set includes 2 x down tube (223 x 28 mm), 2 x seat tube (223 x 28 mm), 1 x head/seat (42 x 42 mm), Optional tubing decal

Lemond Tete De Course (Titanium/carbon)

Digitally re-mastered and produced in quality 70 micron vinyl, a must for all Lemond fans. Not sure if this should be in classic or modern, so I've listed in both! One of the latest from Greg Lemond, built in a mixture of Reynolds Titanium and Carbon. The models that I have seen have the lettering in white with blue panels picked out with white/black stripes at the ends. As these frames have bottle cage eyes, it is not possible to include the printed blue panels as it is not possible to wrap these over the eyes (some say it is but I disagree), so these as with the originals would have to be painted on.To complete the set I have included a printed head badge, although the originals did have a moulded metal or plastic one.

It may be possible to produce these in other colours, but all samples I have seen have been in this colourway.

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Lemond Tete De Course (Titanium/carbon)V2

Digitally re-mastered and produced in quality 70 micron vinyl, a must for all Lemond fans. Not sure if this should be in classic or modern, so I've listed in both! One of the latest from Greg Lemond, built in a mixture of Reynolds Titanium and Carbon. This model has the lettering in black with silver outlines picked out with white/black stripes at the ends. As these frames have bottle cage eyes, it is not possible to include the printed blue panels as it is not possible to wrap these over the eyes (some say it is but I disagree), so these as with the originals would have to be painted on.To complete the set I have included a printed head badge, although the originals did have a moulded metal or plastic one.

It may be possible to produce these in other colours, but all samples I have seen have been in this colourway.

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

LeMond (Trek version)

Set includes 2 x down tube (188 mm x 30 mm), 2 x seat tube (151 mm x 24 mm). Now shipping with 2 pairs of matching stripes for each end of decal (sized to fit steel 28.6 frames). If frame is oversized tubing (possibly Reynolds 853) then please advise info@wanit.co.uk

Marin

Set includes 2 x down tube (250 mm x 23 mm), 2 x seat tube (200 mm x 18mm), 1 x headbadge (42 mm x 50 mm). Please note:the headbadge is printed and should be treated carefully. Best to apply and then lacquer over. The headbadge will always be black on white

Marin Bear Valley

Set includes 2 x down tube (257 mm x 28 mm), 2 x race bred (154 mm x 19 mm), 2 x bolinas (124 mm x 17 mm), 1 x headbadge (42 mm x 50 mm). Please note:the headbadge is printed and should be treated carefully. Best to apply and then lacquer over. The headbadge will always be black on white

Marin Pine Mountain

Set includes 2 x down tube (200 mm x 25 mm), 2 x Pine Mountain (150 mm x 15 mm), 2 x head/seat tube (43 mm x 46 mm),

Merlin

Set includes 2 x down tube (260 mm x 20 mm), 2 x seat tube (208 mm x 16 mm).

Quintana Roo

Set includes 2 x down tube (297 mm x 30 mm), 2 x seat tube (206 mm x 21 mm) 1 x headbadge (62 mm x 30 mm), 2 x forks (38 x 18 mm). Available in various colours and now including matt black, mirror gold and silver

Raleigh Team USA

Taken from a time trial bike form I believe the Olympics in 1884. Set includes 2 x down tube (195 x 29 mm), 2 x seat tube (195 x 29 mm) 2 x campagnolo (100 x 22 mm), 2 x graduating stars for forks. Available in white only. Shown here on ared background (not included)

Richard Sachs

Set includes 2 x Down tube (250 x 29 mm), 2 x forks (120 x 10 mm), 1 x head (50 x 49 mm), 1 x combined seat pattern (270 x 85 mm).,

Ritchey

This version was taken from an oversized steel frame, but would be suitable for standard, alloy or carbon. Set includes 2 x down tube (197 mm x 30 mm), 2 x Seat Tube (197 mm x 30 mm), 1 x head badge (37 x 54 mm).

I offer this version with a tubing decal if required. Other tubing decals may be available info@wanit.co.uk

Ritchey Steel (older)

This version ws taken from an older steel frame with 28.6 tubing. Set includes 2 x down tube (131 mm x 20 mm), 2 x Seat Tube (131mm x 20 mm), 1 x head badge (37 x 54 mm). I offer this version with a tubing decal if required. Other tubing decals may be available info@wanit.co.uk

Ritchey Swiss Cross

Set includes 2 x down tube (235 mm x 35 mm), 2 x Seat Tube (175 mm x 28 mm), 1 x head badge (35 x 50 mm), 2 x Swiss Cross (90 x 16 mm)

Rock Lobster

Suitable for steel frames. For alloy or carbon version please see modern decals
Set includes 2 x down tube (210 mm x 27 mm), 2 x seat tube (168 mm x 22 mm).

Santana

Set includes 2 x down tube (294 mm x 22 mm), 2 x seat tube (153 mm x 11 mm), 1 x headbadge (70 mm x 40 mm).

Scott USA

Set includes 2 x down tube (287 mm x 25 mm), 2 x seat tube (195 mm x 18 mm), 1 x headbadge (37 mm x 25 mm).

Schwinn Peloton

Set includes 2 x Down tube (250 x 23 mm), 2 x top tube  (84 x 12 mm), 1 x head, 1 x seat (51 x 51 mm). Relevant tubing decal also available as option. Available in various colours, although head/seat badge will always be as shown.

Serotta

Set includes 2 x down tube (220 mm x 24 mm), 2 x seat tube (100 mm x 25 mm), 2 x seatstays (80 mm x 20 mm),  1 x headbadge (40 mm x 61 mm).

Serotta V2

Set includes 2 x down tube (220 mm x 24 mm), 2 x seat tube (150 mm x 17 mm), 2 x top tube (98 mm x 11 mm),  1 x headbadge (40 mm x 61 mm), 4 x small 'S' logos for fork crown and seat stays.

Serotta CSI

Set includes 2 x down tube (220 mm x 27 mm), 2 x seat tube (176 mm x 22 mm), 2 x top tube CSI (47 mm x 20 mm),  1 x headbadge (40 mm x 50 mm). Optional tubing decal

Serotta Legend Ti

Set includes 2 x down tube (220 mm x 24 mm), 2 x seat tube (100 mm x 25 mm), 2 x seatstays (80 mm x 20 mm),  2 x Legend Ti, 1 x headbadge (40 mm x 61 mm).

Serotta tiMax

Set includes 2 x down tube (220 mm x 24 mm), 2 x seat tube (220 mm x 25 mm), 2 x tiMax (80 mm x 20 mm),  2 x Ti Max, 1 x headbadge (40 mm x 61 mm).

Specialized

Set includes 2 x down tube (224 mm x 26 mm), 2 x seat tube (186 mm x 22 mm), 1 x headbadge (30 mm x 60 mm).

Specialized FSR

Set includes 2 x down tube (290 mm x 35 mm), 2 x FSR (120 mm x 20 mm), 1 x head badge (42 x 95 mm)

Specialized StumpJumper

Set includes 2 x down tube (240 mm x 30 mm), 2 x seat tube (170 mm x 23 mm) 1 x head (27 x 60 mm)

Trek 850 digital

Digitally re-mastered classic Trek United 850. Printed using the very latest state of the art technology. Set is as shown including down tube, seat tube, top tube, head badge and upper seat tube, 2 x seat tube  Shown here in black with a silver outline.

All printed decals should be lacquered over for a professional and permanent finish. Failure to apply the lacquer can result in premature wear to the print. Comprehensive instructions are available here on my web site, details of which will accompany the decals.

POWDER COATING:
I would advise against using these decals on a frame that has been powder coated unless this has been applied by a professional company who understand cycle frames and not the type who simply do 'iron gates'. Powder coating is without doubt a very tough finish, but can be difficult to adhere to, especially matt finishes. Best to apply to a stove enamelled frame, by an experienced frame sprayer.

Yamaguchi V1

Set includes 2 x down tube (225 x 25 mm), 2 x seat tube (197 x 27 mm), 1 x head/seat (50 x 58 mm), 2 x top tube 'stars' (34 x 34 mm). This set is for an older steel frame with tubing of 28.6 mm (Columbus, Reynolds etc). The sizes can be scaled to suit modern frames with larger tubing info@wanit.co.uk